Bradley Smoker Outdoor Shower HN200 User Manual

Installation  
Instructions  
ADA Compliant HN200  
Recess-Mounted  
Shower with  
• Equa Flo™  
• Accu-Zone™ Infrared  
Control  
• Thermostatic Control  
• Single Valve  
• Air Metering Valve  
• Touch-Time™ or  
• Touch Time™ w/Battery  
Table of Contents  
HN200  
(Valve Right/Seat Left shown,  
Pre-Installation Information . . . . . . . . . . . . 2  
HN200 Components . . . . . . . . . . . . . . . . . . .3  
HN200 Shower Stall Dimensions . . . . . . . .3  
Installation Instructions . . . . . . . . . . . . . . 4-7  
Cleaning Instructions . . . . . . . . . . . . . . . . . .7  
Shower Seat Repair Parts . . . . . . . . . . . . . . .8  
Shower Curtain Repair Parts . . . . . . . . . . . .8  
Valve Left/Seat Right is opposite)  
36" x 36" enclosure is not  
provided as standard equipment  
IMPORTANT  
Read the entire installation manual to ensure proper  
installation of your HN200 shower.  
This manual covers all of the HN200 variations and  
options available, including shower seat and curtain  
installation. Simply omit the steps which do not apply  
to the unit you are installing.  
Valve Left/Seat Right version is shown throughout  
this manual. Valve Right/Seat Left is opposite.  
Plumbing contractor shall be responsible for  
installing shower face plate at the correct height to  
meet accessibility requirements.  
This installation manual and parts list should be filed  
by the owner’s maintenance department.  
P.O. Box 309, Menomonee Falls, Wi 53052-0309  
TEL. 1-800-BRADLEY FAX (262) 251-5817  
215-1189 Rev. F; EN 02-342  
Page 1 of 8  
 
ADA Compliant Recess-Mounted Shower  
HN200  
Installation Instructions  
HN200 Components and Shower Stall Dimensions  
Elbow with Flange  
Showerhead  
Inline Backflow  
Preventer  
Quick Disconnect  
Stainless Steel Hose  
Diverter Valve  
Hand-Held Hose Spray  
with Post-Style Bracket  
Shower Valve  
(Equa-Flo™ shown)  
Recessed Soap Dish  
Shower Face Plate Assembly  
Grab Bar (S53-184)  
18"  
18"  
(457mm)  
(457mm)  
36"  
(914mm)  
15"  
15"  
(381mm)  
36"  
(381mm)  
(914mm)  
14-1/4"  
(362mm)  
max.  
14-1/4"  
(362mm)  
max.  
36"  
4"  
(914mm)  
4"  
36"  
(102mm)  
(102mm)  
min.  
(914mm)  
min.  
VALVE LEFT/SEAT RIGHT  
VALVE RIGHT/SEAT LEFT  
NOTE: Compliance and conformity to local codes and ordinance is the responsibility of the installer.  
Bradley Corporation • 215-1189 Rev. F; EN 02-342  
3
 
ADA Compliant Recess-Mounted Shower  
HN200  
Installation Instructions  
Installation Instructions  
NOTE: Flush the supply lines before making connections.  
NOTE: Install the supply inlets no lower than 48" and no higher than 60" off of finished floor.  
Step 1: Rough in piping for shower  
NOTE: When facing the wall, the supply pipe to the left of the centerline is HOT.  
1. Rough in 1/2" NPT hot and cold water supply piping for valve at the dimension shown in Figure  
1 (piping supplied by installer).  
18"  
(457mm)  
FRONT OF  
SHOWER  
15"  
BACK  
WALL  
2-1/2"  
(64mm)  
TYP.  
(381mm)  
WALL  
OPENING  
OUTLINE  
7-1/2"  
(191mm)  
3-3/4"  
(95mm)  
2"  
(51mm)  
72"  
(1829mm)  
A.F.F.  
45"  
(1143mm)  
2"  
(51mm)  
1/2" NPT  
SUPPLIES  
40"  
(1015mm)  
48"  
(1219mm)  
to 60"  
(1524mm)  
A.F.F.  
48"  
(1219mm)  
A.F.F.  
NOTE: Due to differing state codes, if the  
valve height is different from the indicated  
43" (1091 mm), all dimensions within the  
symbol must be changed by the same amount.  
C
L
20"  
38-1/8"  
(968mm)  
A.F.F.  
Example: If the code approved height is 40",  
then 43" (1091mm) - 40" (1015mm) = 3"  
(76mm). Result: Subtract 3" (76mm) from all  
(508mm)  
Figure 1  
dimensions within the  
symbol.  
NOTE: WALL OPENING RECESS  
TO BE 4" (102mm) DEEP  
4
Bradley Corporation • 215-1189 Rev. F; EN 02-342  
 
ADA Compliant Recess-Mounted Shower  
HN200  
Installation Instructions  
Installation Instructions continued…  
Step 2: Make plumbing connections  
NOTE: Hoses need to be connected to 1/2" NPT pipe supply  
before the shower is fastened to the wall.  
1. Make water supply connections to the stainless steel hoses  
(see Figure 2). Equa-Flo™ and Thermostatic= 1/2" NPT  
Hot and Cold supplies. Single Valve, Accu-Zone™ Infrared  
Control, Air Valve and Touch Time™ = 1/2" tempered  
supply.  
Step 3: Install face plate and grab bar  
1. Position the face plate on the wall. Mark the wall and install  
twelve wall anchors suitable for use with 1/4"-20 x 3/4"  
button head Allen key screws (see Figure 3).  
2. Attach the face plate to the wall with twelve 1/4"-20 x 3/4"  
button head Allen key screws provided (see Figure 3).  
3. Attach the grab bar to the wall.  
• Position the “L” of the grab bar to fit the back wall of the  
shower stall.  
VALVE LEFT  
SEAT RIGHT  
4. Use the flange as a template and mark the six screw hole  
locations and install six anchors supplied by installer for  
1/4"-20 x 1-1/4" flat head Allen key  
Figure 2  
screws (see Figure 3).  
5. Secure the grab bar to the six wall  
anchors using six 1/4”-20 x 1-1/4"  
flat head Allen key screws (provided  
by installer) (see Figure 3).  
1/4"-20 x 3/4"  
BUTTON HEAD  
ALLEN KEY SCREW  
(12) PLACES  
(160-143)  
FACE PLATE  
GRAB BAR  
(S53-184)  
NOTE: ALL WALL  
ANCHORS SUPPLIED  
BY INSTALLER.  
1/4"-20 x 1-1/4"  
FLAT HEAD ALLEN  
KEY SCREW  
Figure 3  
VALVE LEFT - SEAT RIGHT  
Bradley Corporation • 215-1189 Rev. F; EN 02-342  
5
 
ADA Compliant Recess-Mounted Shower  
HN200  
Installation Instructions  
Installation Instructions continued…  
Step 4: Mount shower seat  
NOTE: All anchoring devices (supplied by installer)  
must be carefully selected to insure adequate support for  
the shower seat, given the type of wall construction.  
1. Measure and scribe a horizontal line 16-1/16" above  
the finished floor (see Figure 4).  
2. Position the folding shower seat against the wall  
with the three mounting holes on the seat centered  
on the scribed line.  
• Using the mounting holes as a template, mark the  
three mounting locations on the wall.  
3. Install appropriate anchors (supplied by installer) for  
1/4" sheet metal screws in the wall at the three  
mounting locations.  
Figure 4  
4. Mount the shower seat to the wall with the  
three 1/4" sheet metal screws (supplied) at  
the anchored mounting locations.  
Figure 5  
• Position the seat support tube in the  
support bracket as shown in Figure 5. The  
tube should rest on the bottom of the front  
plate.  
NOTE: When seat is properly installed, it should  
decline downward from back to front 2° to 3° for  
water drainage.  
5. Place the support bracket against the wall  
and adjust the bracket vertically until the  
shower seat is level in down position.  
• Using the mounting holes on the support  
bracket as a template, mark the four  
mounting locations on the wall.  
6. Install appropriate anchors (supplied by installer) for  
1/4" sheet metal screws in the wall at the four  
mounting locations.  
7. Mount the support bracket to the wall with the four  
1/4" sheet metal screws (supplied) at the anchored  
mounting locations.  
Step 5: Install curtain rod  
Figure 6  
1. Measure and cut the stainless steel curtain rod to fit  
the shower stall opening.  
2. Mount one shower rod flange 80" (2032mm) from the floor as close to the opening of shower stall as  
possible with two #10-13 x 2" Phillips-head screws provided (see Figure 6).  
• Insert one end of the shower rod into the flange.  
• Slide the other shower rod flange onto the shower rod.  
3. Position the shower rod and flange at the same dimensions as the first flange but on the opposite side  
of the shower stall opening.  
4. Secure the flange to the wall with two #10-13 x 2" Phillips-head screws provided.  
5. Install the ten hooks onto the curtain rod and hang the curtain onto the rod.  
6
Bradley Corporation • 215-1189 Rev. F; EN 02-342  
 
ADA Compliant Recess-Mounted Shower  
HN200  
Installation Instructions  
Cleaning and Maintenance Instructions for Stainless Steel  
Material Description: Stainless steel is extremely durable, and maintenance is simple and inexpensive.  
Proper care, particularly under corrosive conditions, is essential. Always start with the simplest solution and  
work your way toward the more complicated.  
Routine cleaning: Daily or as often as needed use a solution of warm water and soap, detergent, or ammonia.  
Apply the cleaning solution per the manufactures instructions and always use a soft cloth or sponge to avoid  
damaging the finish.  
Stubborn Stains: To remove stains from stainless steel use a stainless steel cleaner and polish such as Ball®  
stainless steel cleaner or a soft abrasive. Always follow the manufactures instructions and apply in the same  
direction as the polish lines.  
IMPORTANT: NEVER USE ORDINARY STEEL WOOL OR STEEL BRUSHES ON  
STAINLESS STEEL. ALWAYS USE STAINLESS STEEL WOOL OR  
STAINLESS STEEL BRUSHES.  
Special Situations for Material  
Fingerprints and Smears: To remove fingerprints or smears use a high quality stainless steel cleaner and  
polish in accordance with the manufactures instructions. Many of these products leave a protective coating  
the helps prevent future smears and fingerprints.  
Grease and Oil : To remove grease and oil use a quality commercial detergent or caustic cleaner. Apply in  
accordance to the manufactures instructions and in the direction of the polish lines.  
Precautions: Avoid prolonged contact with chlorides (bleaches, salts), bromides (sanitizing agents),  
thiocyanates (pesticides, photography chemicals, and some foods), and iodides on stainless steel equipment,  
especially if acid conditions exist.  
IMPORTANT: DO NOT PERMIT SALTY SOLUTIONS TO EVAPORATE AND DRY ON  
STAINLESS STEEL.  
The appearance of rust streaks on stainless steel leads to the belief that the stainless steel is rusting. Look for the  
actual source of the rust in some iron or steel particles which may be touching, but not actually a part of the  
stainless steel structure.  
NOTE: Strongly acidic or caustic cleaners may attack the steel causing a reddish film to appear. The use of  
these cleaners should be avoided.  
Brand Names: Use of brand names is intended only to indicate a type of cleaner. This does not constitute an  
endorsement, nor does the omission of any brand name cleaner imply its inadequacy. Many products named are  
regional in distribution, and can be found in local supermarkets, department and hardware stores, or through your  
cleaning service. It is emphasized that all products should be used in strict accordance with package instructions.  
Bradley Corporation • 215-1189 Rev. F; EN 02-342  
7
 
ADA Compliant Recess-Mounted Shower  
HN200  
Installation Instructions  
Shower Seat Repair Parts  
158-010 Left Hand Plastic Seat (Valve Right)  
158-011 Right Hand Plastic Seat (Valve Left)  
Shower Curtain Repair Parts  
Curtain Pre-pack S30-068  
ITEM  
PART NO.  
DESCRIPTION  
QUANTITY  
1
170-006  
170-006D  
170-006E  
151-001  
269-367  
150-157  
P10-412  
Vinyl Shower Curtain  
Duck Shower Curtain  
Herculite Shower Curtain  
Curtain Hook  
1
2
3
4
5
10  
Curtain Rod  
1
Shower Rod Flange  
#10-13 x 2” Phillips-Head Screw  
2
1 Bag (4 Screws)  
8
Bradley Corporation • 215-1189 Rev. F; EN 02-342  
 

Belkin Network Card 8820 01363 User Manual
Belkin Switch F5U407 User Manual
Black Decker Power Hammer 1 1 2 User Manual
Breville Waffle Iron BSG520XL User Manual
Brother Network Cables QL 580N User Manual
Brunton Coffeemaker 81 100730 User Manual
Canon Camcorder XM2 PAL User Manual
Canon Camera Flash 166 A User Manual
CFM Fan APW 0906 User Manual
Char Broil Gas Grill 463210510 User Manual